kolektor PROECO JNMK - 20 SUS (bezciśnieniowy)
kolektor PROECO JNMK - 20 SUS (bezciśnieniowy)
kolektor PROECO JNMK - 20 SUS (bezciśnieniowy)
kolektor PROECO JNMK - 20 SUS (bezciśnieniowy)
kolektor PROECO JNMK - 20 SUS (bezciśnieniowy)
kolektor PROECO JNMK - 20 SUS (bezciśnieniowy)
kolektor PROECO JNMK - 20 SUS (bezciśnieniowy)

Kolektor PROECO MK-30 SUS (bezciśnieniowy)


EAN-13: 5902734701572

Solar collector PROECO MK-30 SUS (non-pressure) 
- 30 vacuum tubes
- Stainless steel frame

2,600.00 PLN

2.113,82 tax excl.

Possible delivery within 10 days
In Stock
  1. Non-pressure collector PROECO MK-30 SUS: 

- 30 tubes with a triple absorption layer ALN/AIN-SS /CU
- stainless steel frame (with possibility of installation on both oblique and flat surface)
- collector manifold made of stainless steel (inside and outside)



An ideal solution for obtaining utility hot water for camping sites, farms, and for the heating of swimming pools.



The solar collector consists of vacuum tubes made of borosilicate glass. High operational safety of borosilicate glass has been achieved thanks to the use of an appropriate mix of SiO2 and B2O3 oxides, which results that the product has high chemical resistance as well as extraordinary purity and uniformity. Borosilicate glass is environment-friendly and can be recycled many times. The process of thermal annealing (hardening) was also used.  Together with the low thermal expansion typical for borosilicate glass gives it a particularly high resistance to changes of temperature in comparison to standard glass. Tubes are resistant to hail size up to 25 mm. The use of tubes with a diameter of 47 mm and 58 mm allows concentric placement of one inside the other. The air between the pipes is pumped out, and the pipes are welded together. 

Solar radiation on the absorber on the inner tube is converted into thermal energy and causes heating of the interior of the tube. The vacuum between the tubes is an excellent insulator and prevents heat loss. The collector manifold is made of SUS 304-2B stainless steel and is insulated with polyurethane foam.


 Principle of operation:

There is water in both in the tank and the tubes. Under the influence of sunlight, the water in the tubes heats up. Thanks to convective movements, it goes up to the tank. Water circulates continuously between the tank with water and the vacuum tubes, which causes a constant increase of temperature. of water. High efficiency of the collector results from the ability to absorb diffused radiation (for example, on cloudy days) and maximum reduction of heat loss. 



- Higher efficiency of vacuum collector in comparison to standard flat collector.
- Simple design, low failure rate - tube lifespan of over 15 years.
- Easy servicing and self installation possible.

 Installation and operating instructions

PROECO MK 20 SUS Instructions.pdf

Frame color silver
Manifold color silver
------------------------------ COLLECTOR:
Number of vacuum pipes 30
Heat pipe use nie
Size of vacuum tubes diameter: 58 mm. outside /47 mm. inside, wall thickness: 1,6 ± 0,15 mm., length: 1800 mm.
Type of absorber (aluminum nitride with copper and steel layers) CU/SS-ALN(H)/SS-ALN(L)ALN
Efficiency of the absorption α = 0.92~0.96 (AM1.5)
Lossy emission ε = 0.04~0.06 (80℃ ± 5℃)
Degree of vacuum P. ≤5.0X10ˉ³ (PA)
Temperature of stagnation 260~300℃ (inside empty tube)
Average heat loss ULT 0.4~0.6 W/(m2~﹡℃)
Resistance to heil Φ25 mm
Lifespan > 15 years
------------------------------ FRAME:
materiał stainless steel 
Resistance to wind 180 km/h

Reference: PROECO JNMK-30 SUS
3. Hot water outflow:
under the influence of gravity
4. Installation on an surface:
for flat or sloping to 80 degrees
Number of vacuum tubes (pcs.):
Size of the vacuum tubes (mm.):
58 mm / 1800 mm
Use of Heat-Pipe:
stainless steel SUS 201

Related products

Back to top